Park-It Parking Curb - GNR Technologies

Features

Unlike concrete or plastic, which necessitate frequent replacements, recycled rubber car stops are safer and more durable. Molded highly reflective tape ensures visibility and pedestrian safety. The GNR Park-It car stop is constructed of 100% recycled rubber.

The recycled rubber parking curb come with pre-molded holes and can be shipped with anchoring spikes or lag bolts for installation. They are lightweight (34 lbs.) and can be easily installed by one person. The flexible design conforms to the contour of uneven road surfaces. Designed to withstand extreme temperature variants, the car stops are resistant to moisture, oil, and ultraviolet light. They will not warp, crack, chip, or rot.

Park-It car stops are available in 22", 3', 4', and 6' lengths. In-molded reflective tape is available in yellow, white, or (handicap) blue.

Car stops are covered by a 3 year warranty.

Park It car stops are:

Made of 100% recycled rubber
Long lasting and cost efficient
Ideal for indoor or outdoor parking
Will not chip, crack, or fade
High visibility at night
Simple installation by one person
Can be installed on any road surface
Resistant to ultraviolet light, moisture, oil, and extreme temperatures
Temporary or permanent installation
1/10th the weight of standard concrete curb
Do not require heavy machinery
Maintenance free
3 year warranty

www.SafestParkingProducts.com

Park It car stops have been used in the following locations:

WalMart
Target
St. Frances Hospital
McDonald's
Burger King
Eckerd
Dunkin Donuts
Bank One
Hilton Hotels
Montreal Children's Hospital
El Conquistador resort

Installation Locations:

Surface parking lots

Multi-level parking lots


Dimensions

		Park-It Curb Dimensions: (L) 22" x (W) 6" x (H) 4" - 9 lb. (2 per parking stall; 1 per wheel location) (L) 3' x (W) 6" x (H) 4" - 17 lb. (L) 4' x (W) 6" x (H) 4" - 22.5 lb (L) 6' x (W) 6" x (H) 4" - 34 lb.

Technical Specs

Product Name:

Rubber Car Stop

Models:

6', 4', 3' 22" lengths

Product Description :

1. Material: compression molded composite of the 100% recycled rubber and polyurethane prepolymer
2. Physical properties of the rubber composite:
a) Density 0.6 oz/cu in (ASTM C642)
b) Durometer Hardness 65A ± 7 (ASTM D2240)
c) Tensile Strength* minimum 210 psi (ASTM D412)
(* main structural areas)
d) Compression deformation 10% at 70psi, 68°F (ASTM D575)
e) Brittleness at Low temperature: -40°F (ASTM D746)
f) Freeze and thaw when exposed to deicing chemicals (ASTM C672)
g) Coefficient of thermal expansion 8 x10-5 in/in/°F (ASTM C531)
h) Weathering 70 hours at 158°F (ASTM D573)
- hardness retained
100% (± 5%)
- compressive strength 100% (± 5%)
- tensile strength 100% (± 5%)
- elongation retained 100% (± 5%)
3. Available models: 6', 4', 3' and 22" lengths
4. Finishing: Black with in-molded reflective pavement marking tape in yellow, blue or white parallelograms

Componets:

a) 100% recycled rubber from car and truck tires (NR, SBR)
b) polyurethane prepolymer for rubber granules
c) yellow, white, or blue durable and reflective in-molded pavement marking tape

Installation Guide

Components

Park-It car stops
1/2" (diameter), 14" (length) rebar spikes for asphalt or lag bolts with metal shields for concrete - available at GNR

What You Need

Gloves, safety glasses
Traffic cones, drums or barricades for securing the site
Mallet
Heavy duty electric drill
1/2" masonry bit, and if installed with the lag bolts: a masonry bit required for the metal shields - consult bit size on side of shield
A drive socket and a power tool for installation of the lag bolts

The flexible design of the Park-It parking curb allows the product to conform to the contour of uneven road surfaces and can be installed on both asphalt and concrete.

Installations Instructions for Asphalt: Installation of Park-It car stops with spikes

Step 1.

Drill 1/2" diameter holes (3 - 4" in depth) in the asphalt through the product's holes.

Step 2.

Drive 1/2" rebar spike (14" long) through the holes in the product.

Installation Instructions for Concrete: Installation of Park-It car stops with lag bolts and metal shields

Step 1.

Use 1/2" or 5/8 lag bolts (6" long).

Step 2.

Drill 1/2" diameter pilot holes (3 - 4" in depth) through the product's installation holes.

Step 3.

Remove the product; re-drill the holes for the diameter and depth required by the metal shields

Step 4.

Install the metal shields, re-position the product and bolt with lag bolts.

Maintenance

Park-It curbs require minimal maintenance. Periodically inspect the bolts and tighten if necessary.

Some images of installation locations of the Park-It Car Stop: